HF -Ausgangsbrett mit SWR/PWR -Pickup (7/16 Anschluss) 2500W

    HF -Ausgangsbrett mit SWR/PWR -Pickup (7/16 Anschluss) 2500W

    2500W RF -Ausgangsbrett mit SWR/PWR -Pickup (7/16 Anschluss)

    RF -Ausgangsplatine für 7/16 Stecker mit SWR/PWR -Richtungskuppler

    Jetzt mit Teflon -Laminat und Frequenz im FM -Rundfunkband!

    kompensiert

    Sammeln Sie mit dem Kauf dieses Artikels bis zu 3 Treuepunkte. Ihr Warenkorb hat insgesamt 3 Treuepunkte die umgewandelt werden können in einen Gutschein im Wert von € 0,60.


    € 49,99

    Output board options 

    • 2500W RF Output Board with SWR/PWR and 15cm semi-rigid

    • 2500W RF Output Board with SWR/PWR for 7/16 connector

    Rabatt auf Ihre Bestellung Rabatt auf Ihre Bestellung
    Kostenloser Versand Kostenloser Versand in NL
    Volumenrabatt Volumenrabatt
    Bonus-System Bonus-System
    Sichere Zahlung Sichere Zahlung
    Geld-zurück-Garantie Geld-zurück-Garantie
    Trustpilot Trustpilot

    Mengenrabatt

    Menge Rabatt Sie sparen
    2 2% Bis zu € 2,00
    4 4% Bis zu € 8,00
    6 6% Bis zu € 18,00
    8 8% Bis zu € 31,99
    10 10% Bis zu € 49,99

    Mehr Infos HF -Ausgangsbrett mit SWR/PWR -Pickup (7/16 Anschluss) 2500W

    Product discription:


    A simple solution that could make your life so much easier. If you ever wanted to mount a 7/16 connector to your enclosure and connect coaxial cable to it in a clean and effective way without adding parasitic inductance and making it all look like a mess, you probably noticed that this isn't so easy to do. We do have a simple solution, however. This small PCB screws tightly and directly to the panel mounted 7/16 connector (see pictures) and enables a clean, electrically excellent and also good looking contact. To top it off, it also contains a small stripline directional coupler. Three-pin solder header provides ground and two voltages, one for SWR and the other for POWER. You can now measure this voltage to determine your output POWER or SWR. It is also possible to use this board to simply build SWR protection.

    Coaxial cable can be easily soldered to the terminals as shown on the photos. We recommend teflon based coaxial cable for such interconnection wiring since teflon isolation does not melt when soldered or heated due to high power level. Boards with installed 15cm of semi-rigid 50ohm teflon cable are also available. This cable is also prepared for soldering on its free end, making installation extremely simple.

    The boards are now produced on TEFLON laminate and take much higher power, also they are freqency compensated so a reading at 108MHz and 88MHz produces the same readings.

     

    Technical facts:


    - Size: , PTFE (TEFLON) laminate
    - Power handling: 0-2500W with heatsinking
    - Frequency range: 0-500MHz (Frequency compensated for equal reading inside entire FM broadcasting band)
    - Connectors supported: panel-mounted 7/16 or some versions of panel mounted 7/8 (if you can't find it email)
    - Includes: PCB and all components, connector and screws not included

    3 andere Produkte in der gleichen Kategorie - RF FM -Ausgangsbretter und SWR -Pickup -Boards